Custom Metal Buildings Ayden, NC

Charcoal metal garage with two roll-up doors and a lean-to

Ayden NC — Pitt County · South of Greenville

The usual mistake with custom metal buildings in Ayden, NC is choosing the size first and the site second. The water table here sits closer to the surface than most newcomers expect, so a low corner of the yard can hold water after a hard summer thunderstorm. Watch the property through one heavy rain, pick the spot that stays dry, and only then settle the width and length.

From there we do the rest. At our Farmville plant we roll-form 29-gauge steel, and we deliver and install the finished building in Ayden, Grifton and along the Winterville corridor south of Greenville, with no separate builder needed for the steel. Tobacco and farm history still shape how Pitt County parcels get used, and shops, equipment barns and mixed-use storage buildings are everyday orders. Call (252) 414-5105.

Call (252) 414-5105

Get a Free Quote
Reputation and Trust

No contractor in the middle

We build and install the steel building ourselves, so nobody else needs to be hired for it.

Diverse Product Range

Sized to your Ayden site

Widths, lengths and leg heights are quoted for the Pitt County site you own.

power 2

Made in Farmville

The 29-gauge steel is roll-formed in Farmville; Greenville has sales lots and no plant.

Locations

Greenville walk-in lot

Our sales lot is at 1046 Greenville Blvd SW.

Support

Call us

(252) 414-5105 is the number for questions and quotes.

delivery truck

Delivery at no charge

Free within 100 miles, which covers Ayden, Grifton and the Winterville corridor.

money_1

Rent-to-own terms

No credit check is run on buildings that qualify.

ECOPM28

One company from coil to finished building

Making the building, hauling it to your site and putting it up are all jobs we do ourselves, so you can skip hiring anyone else for the steel. Phone (252) 414-5105 with your questions.

Gray metal garage with two open doors and a lean-to under trees

Custom metal buildings in Ayden, sized for south Pitt County

Ayden lies along NC 11, south of Greenville, among farm tracts, warehouse edges and residential lots, and any of them can use steel without a general contractor’s markup on top. We form your building from coil at the Farmville plant, then fit the width, length, doors and roof style to your parcel instead of to a national kit design.

Red metal building with open bays on a wide concrete slab

Old tobacco ground put to new use

Land around Ayden and Grifton that once grew tobacco and row crops now often holds equipment storage, a side business or a workshop. A clear-span frame has room for tractors and trailers, a lean-to shelters implements, and an insulation package takes the edge off summer heat in a shop. We size the openings for the equipment you really run.

The East Carolina Outdoor Products Greenville lot seen from above the road

Delivery to Ayden, Grifton and Winterville, and our Greenville lot

Delivery is free within 100 miles, which takes in Ayden, Grifton, Winterville and the area south of Greenville. To visit, go to our walk-in lot, East Carolina Outdoor Products at 1046 Greenville Blvd SW in Greenville, NC 27834. It is not the plant, because manufacturing stays in Farmville. For anything else, call (252) 414-5105.

ECOPM32

What a custom metal building should mean for an Ayden lot

Any seller can call a building custom, so the better question is what you get to change. Leg height, width and length should move in small steps rather than force a pick among three stock sizes. Put openings where the driveway runs and the work gets done. Framing and anchors should be set for Pitt County and not borrowed from a brochure.

Where a permit applies, inspectors look for certified drawings made out for the address named on the permit. A lean-to is a cheaper way to add room than widening the building: one open side can shelter firewood, a boat or a tractor.

Start from a sketch of your lot: the driveway, the side the weather arrives on and a list of what goes inside. Bring it to us, or test a rough layout inside the 3D designer first.

Tan metal garage with a lean-to and concrete driveway

Pitt County ground around Ayden: choosing the spot for the pad

Ayden’s Collard Festival comes every September, in the middle of Pitt County barbecue country. The ground is level, a sandy loam on top of clay typical of the inner coastal plain, and groundwater lies nearer the surface than newcomers tend to expect. After a hard summer thunderstorm, walk the property and see which corners hold water; the building should go somewhere else.

Hurricane Floyd in 1999 and Hurricane Matthew in 2016 reached the county mostly as rain, and for days afterward the Tar River and the Neuse River ran over their banks. Wind counts as well, but for most of Pitt County the practical priorities are good drainage, a pad that sheds rain and anchors suited to the soil. If the lot lies close to a creek or river, look up the county flood map beforehand. It takes about five minutes and can head off an insurance headache.

Specifications

  • Plant: Farmville, NC — roll-forming manufacturer
  • Main office (lots): East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834
  • Greenville lots: 1046 Greenville Blvd SW
  • Primary phone: (252) 414-5105
  • Service area: Ayden · Grifton · Winterville · Greenville south · Pitt County
  • Widths: 12′ – 60′ clear span
  • Lengths: 20′ – 100’+ in 5′ increments
  • Leg heights: 6′ – 20′
  • Panels: 29-gauge standard, 26-gauge upgrade
  • Roof styles: Regular, A-frame boxed eave, vertical
  • Delivery: Free within 100 miles

Common Questions

Do I have to bring in my own crew to put up an ECOP steel building?

No. Manufacture, delivery and setup of the steel building are all handled by us; if you want to talk it over, the number is (252) 414-5105.

Where do I go to buy a custom metal building in Ayden, NC?

Phone ECOP at (252) 414-5105. The steel is made in Farmville, and we bring finished buildings to Ayden, Grifton and the Winterville corridor. If you would like to look around first, our walk-in lot is at 1046 Greenville Blvd SW in Greenville.

Is any manufacturing done at the Greenville lot?

No. The steel is formed in Farmville; the Greenville location only sells, and only to walk-in visitors.

How far can a steel building be customized for a site in Ayden, NC?

Wind certification, roof style, colors, openings and lean-tos can all be set to suit your Pitt County site, along with the width, length and height. One-off architectural designs fall outside what we do, and we say so at the start.

Will the inspector in Pitt County want engineered drawings for my building?

A permit is needed for most permanent buildings on a foundation, and certified drawings come from us whenever the inspector requests them. Call (252) 414-5105.

Is delivery to Ayden, Grifton or Winterville free?

Yes. Delivery and professional setup cost nothing within 100 miles, and all three towns sit well inside that circle around Farmville.

Is rent-to-own with no credit check available in Ayden, NC?

Qualifying buildings, yes. For the terms in force at present, ask us at (252) 414-5105.

Your Ayden price within 24 hours

Tell us the size you are after, the county and what the building will hold, and a figure based on current steel pricing comes back to you. Nothing obliges you to proceed, and should a different size serve you better, we will point that out.

Request a Quote Design It in 3D