Custom Metal Buildings Florence, SC

White metal building with a lean-to over a concrete pad

Florence SC · Pee Dee · I-95 / I-20 Corridor

A common mistake with custom metal buildings in Florence, SC is taking the word custom at face value. Every seller uses it, so ask which parts can really change: the length, the bay layout, the door positions and the certification. With us, the lot you own drives all of those, not a national catalog. Our plant in Farmville, NC roll-forms the 29-gauge steel, and we serve Florence, the Pee Dee hub where I-95 meets I-20, with Darlington close by.

Florence here is Florence County in South Carolina, not North Carolina. Our own crews put the building up, so for the steel you need no separate builder. Free delivery covers sites within 100 miles of one of our lots, and Florence usually lies beyond that, so ask at (252) 414-5105 for a straight Pee Dee delivery quote. The Greenville, NC lots exist for sales; the plant, where the steel is made, is in Farmville.

Call (252) 414-5105

Get a Free Quote
Reputation and Trust

No builder to hire

Our crews build and set up the steel building, so there is no second contractor to hire for that part.

Regional Focus

Pee Dee service area

Florence County, SC, on the I-95 and I-20 corridor, with Darlington close by.

power 2

Farmville plant, Greenville lots

Steel is formed in Farmville. Our sales lots are in Greenville, NC; East Carolina Outdoor Products is at 1046 Greenville Blvd SW in Greenville, NC 27834.

Support

Call for a quote

Reach us at (252) 414-5105 with questions or to ask for a Florence delivery quote.

delivery truck

Delivery to Florence

No charge inside 100 miles of an ECOP lot. Florence is priced separately, and we deliver there too.

money_1

Rent-to-own

No credit check is run when a qualifying building goes rent-to-own.

Quality Assurance

Certified drawings

We provide them whenever Florence County or a neighboring jurisdiction requests them.

ECOPM28

Nobody else to hire for the steel

From manufacturing to delivery to setup, the work is ours. For the steel itself you will not be hiring a builder or a contractor. Questions about a Florence job can go to (252) 414-5105.

Gray barn-style metal garage with two doors and side lean-tos

Custom metal buildings at the Pee Dee crossroads

The interstates I-95 and I-20 cross at Florence, the hub of the Pee Dee, and Darlington Raceway country lies close by along with the shops, farms and contractor yards of Florence County. Each custom metal building we quote comes out of the Farmville plant, and the lot you actually own in the Florence area dictates its length, bay layout, door positions and certification, not a catalog entry.

Red metal building with open bays on a wide concrete slab

Options open to you around Florence

Standard increments set the width and length, and leg heights reach 20′. Roofs come regular, A-frame or vertical. Windows, wainscot and insulation can be added, along with framed openings and lean-tos. Farm, shop, garage and logistics-yard packages are common along I-95 and I-20 and near Darlington. Before you sign, we sort out which options change the structure and which only change the look.

Dark green metal building with a roll-up door

Florence, Darlington and the rest of the Pee Dee

To reach us, ring (252) 414-5105 or stop in at East Carolina Outdoor Products, 1046 Greenville Blvd SW in Greenville, NC 27834, where the Greenville lots let you look at framing samples. After that we arrange delivery from Farmville to Florence and across the Pee Dee in South Carolina. Inside 100 miles of one of our lots delivery is free. Florence usually lies farther out, so its freight is quoted up front, and the building still arrives installed.

Tan metal garage with two doors and an open lean-to

What custom should mean when you order a metal building in Florence

Ask any seller whether a building is custom and the answer will be yes, so ask something more useful: which parts can I actually change? Look for width, length and leg height that adjust in small steps instead of three fixed sizes. Look for doors and windows that can go where you drive in and where you work. And look for framing and anchoring that were specified for Florence County, not copied from a catalog sheet.

That final point matters when a permit is required, since the inspector will expect certified drawings made out for the address on the permit. Lean-tos are another good use of custom. A bay left open down one side shelters a tractor, a boat or the firewood, and it is much cheaper than widening the entire building. Sketching your lot is the easiest first step: show the driveway, show which way the weather arrives from, and list the contents. You can bring the sketch to us or test the layout in the 3D designer.

Gray barn-style metal building with four garage doors

Storms, rivers and anchoring in Florence County

The recent storms set the terms for building here. When Matthew came through in 2016, and again with Hurricane Florence in 2018, the rivers rose after the winds were gone: the Lumber, the Little Pee Dee and the Black all flooded the communities beside them. So the first siting question is how close your land is to a creek or to low ground, and the county flood map is where you check.

Around Florence the farmland is flat and sandy, planted in tobacco, cotton and soybeans or kept in timber, and threaded with slow rivers and swamps. Two decisions matter most for a steel building on that ground: where the water goes and what holds the frame down. Build the pad up, compact it well and choose anchors meant for sandy soil. Those two steps do more to extend the building’s life than any upgrade a passer-by would notice. Away from standing water, summer heat and humidity are the real enemy, and they are why a pale roof, a vapor barrier and good ventilation earn their place.

Specifications

  • Main office: East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834
  • Primary phone: (252) 414-5105
  • Plant: Farmville, NC roll-forming (not Greenville)
  • Service area: Florence SC · Pee Dee · I-95 / I-20 corridor
  • Nearby: Darlington, Timmonsville, Lake City, Hartsville
  • Widths: 12’–60′ clear span
  • Panels: 29-gauge standard, 26-gauge upgrade
  • Delivery: Free within 100 mi of any ECOP lot; Florence quote on call

Common Questions

If I order from ECOP, do I have to find someone to put the building up?

No. Manufacture, delivery and setup of the steel building are all ours. You can reach us at (252) 414-5105.

Where can I buy a custom metal building in Florence, SC?

From East Carolina Outdoor Products, at (252) 414-5105. We roll-form the steel in Farmville, NC and deliver to Florence and the South Carolina Pee Dee. Our main office is at 1046 Greenville Blvd SW in Greenville, NC 27834.

Are the buildings made at the Greenville location?

No. They are made at our plant in Farmville, NC. The Greenville, NC lots are for selling. Phone (252) 414-5105.

Will I pay for delivery to Florence, SC?

Free delivery stops at 100 miles from our lots, and Florence usually lies beyond that. We still deliver from Farmville, and the cost is quoted when you phone (252) 414-5105.

Do I need engineered drawings for a building in Florence County?

A permit is usually needed for a permanent building on a foundation. If your inspector asks for certified drawings, we provide them. Questions go to (252) 414-5105.

Is rent-to-own offered, and does it involve a credit check?

Yes, on qualifying buildings, and there is no credit check. Ask us at (252) 414-5105.

A Pee Dee price in 24 hours

Send the size, the county and the purpose, and within 24 hours a price built on current steel costs reaches you. No obligation attaches to it, and if a different size would serve you better, you will hear that from us too.

Request a Quote Design It in 3D