Custom Metal Buildings Greenville, SC

Gray barn-style metal building with four garage doors

Greenville SC · Upstate · Greenville County SC

Custom metal buildings in Greenville, SC start with decisions you make before anything is built: how wide, how long and how tall the building should be, what kind of roof it needs and where the openings belong. Bring those decisions to us with a sketch of the lot and a list of what will go inside, and we will fit the building to your Greenville County site.

Our base is Eastern North Carolina. The 29-gauge steel is roll-formed at the plant in Farmville, and the Greenville we sell from is Greenville, NC, where the lots are for sales only and nothing is manufactured. The Greenville in question here is the one in South Carolina, not the one in Pitt County. We work across the Upstate: the I-85 corridor, Greenville County, Spartanburg and Anderson. Our own crew builds and installs, so no separate contractor is needed for the steel. Delivery and setup are free for sites within 100 miles of an ECOP lot; Greenville, SC is beyond that, so call (252) 414-5105 and we will quote the Upstate delivery straight.

Call (252) 414-5105

Get a Free Quote
Relocated

Built and installed by us

Our own crew puts the steel building up, so no separate contractor is involved.

Regional Focus

Greenville County and the Upstate

Our service area is the I-85 corridor, Spartanburg, Anderson and Greenville County SC, not Pitt County NC.

power 2

Farmville plant, Greenville NC lots

Buildings are made in Farmville. Our Greenville NC lot sells only: East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834.

Support

Phone

(252) 414-5105 for questions and quotes.

delivery truck

Delivery to the Upstate

Delivery is free inside 100 miles of an ECOP lot; Upstate SC deliveries are quoted, and we make them.

money_1

Rent-to-own

Qualifying buildings can be rented to own with no credit check.

Quality Assurance

Certified drawings

We supply them when Greenville County SC or a nearby jurisdiction asks.

Red metal garage with two roll-up doors and a carport lean-to

Why there is nobody else to hire

A crew from ECOP makes the building, brings it to your site and puts it up. Because of that, the steel building itself needs no outside builder or contractor. Call (252) 414-5105.

Tan metal garage with two roll-up doors and side lean-tos

Greenville, South Carolina, and a plant in Farmville

Greenville, SC is in Greenville County, on the I-85 corridor and close to Spartanburg and Anderson. Do not confuse it with Greenville, NC in Pitt County: our North Carolina location is a sales lot at 1046 Greenville Blvd SW, Greenville, NC 27834, and the plant that makes the buildings is in Farmville, NC. For a South Carolina site we fit the bay layout, openings and certification to your Greenville County lot.

Tan metal garage with two doors and an open lean-to

Custom metal buildings near Greenville, SC: what you can change

Width and length are chosen in standard increments, and the legs can be up to 20 feet tall. For the roof you pick regular, A-frame or vertical. Openings are framed for roll-up doors and for walk-in doors, and insulation, lean-tos, wainscot and windows can be added. Along I-85 the common orders are shops, garages, barns and contractor yards, and before you sign we sort what is structural from what is only cosmetic.

White metal building with open bays, with a truck and equipment trailer nearby

Delivery to the Upstate and along I-85

Call (252) 414-5105, or visit East Carolina Outdoor Products at 1046 Greenville Blvd SW in Greenville, NC. At the lot you can walk through framing samples; afterward we schedule delivery from the Farmville plant to your Upstate site. Any site within 100 miles of an ECOP lot gets delivery free, while freight to Greenville, SC is quoted plainly, and we still deliver and install.

Red metal building with open bays on a wide concrete slab

Custom metal buildings: which parts should you be able to change?

Custom is a word every building seller uses, so test it with three questions. Can you set the building’s width, its length and the height of its legs in small steps, or must you pick from three stock sizes? Can the doors and windows sit where the driveway and the job call for them? And will the framing and anchors be worked out for your county rather than taken from a catalog?

The last question matters most where a permit applies, because inspectors expect certified drawings tied to the permit’s address. Lean-tos are a second place where custom pays: firewood, a boat or a tractor can all sit in an open bay down one side, and that costs far less than widening the building.

Start with a sketch of the lot: mark where the driveway runs and which way the weather arrives from, and list everything that will go inside. Bring that sketch to us, or lay it out in the 3D designer beforehand.

Tan and brown metal garage with two roll-up doors

Greenville, SC: storms, red clay and sloping ground

Heavy rain, not wind, is what tropical systems usually bring to the Upstate. Helene in 2024 was different, because it brought both. Between storms, a building here is worn down by hail, by falling limbs, by summer thunderstorms and by the odd ice storm. Water, leaves and ice run off a vertical roof more readily than off a horizontal one, and the framing and anchoring should be specified for Greenville County.

Greenville, SC is a Blue Ridge foothills city on the Reedy River and I-85, and the ground is red clay and rolling. After cutting and compacting, clay makes a firm base. The catch is that few lots are flat, which makes the grading plan more important here than near the coast. Tell us how much the footprint slopes and where runoff goes at the moment; no other detail helps more when someone is pricing site preparation. Extra leg height pays for itself the day a boat headed for Hartwell or Keowee has to fit under the roof.

Specifications

  • Main office: East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834
  • Primary phone: (252) 414-5105
  • Plant: Farmville, NC roll-forming (not Greenville)
  • Service area: Greenville SC · Greenville County SC · Upstate / I-85
  • Nearby: Spartanburg, Anderson, Mauldin, Simpsonville, Travelers Rest
  • Widths: 12’–60′ clear span
  • Panels: 29-gauge standard, 26-gauge upgrade
  • Delivery: Free within 100 mi of any ECOP lot; SC Upstate quote on call

Common Questions

Will I have to hire a builder for an ECOP metal building?

No. We make the steel building, bring it and erect it. Call (252) 414-5105.

Is your Greenville the one in South Carolina or the one in North Carolina?

South Carolina, in the Upstate. That means Greenville County, not Pitt County, NC. The address we have in Greenville, NC, 1046 Greenville Blvd SW, sells only; we roll-form the steel at the plant in Farmville, NC.

Are the buildings made in Greenville?

No, they are made in Farmville, NC. In Greenville, NC we only sell, from lots with no plant. Call (252) 414-5105.

Does free delivery extend to Greenville, SC?

No. Free delivery and setup reach only as far as 100 miles from an ECOP lot, and Greenville, SC is past that. We still deliver from Farmville, so call (252) 414-5105 for a delivery quote.

Do I need engineered drawings for a building in Greenville County, SC?

A building that is permanent and sits on a foundation will usually need a permit. If the inspector asks for certified drawings, we provide them. Call (252) 414-5105.

Is a credit check required for rent-to-own?

Not on qualifying buildings. Ask us at (252) 414-5105 for the terms currently offered.

Get a price for your site within 24 hours

Describe the building you want: its size, the county and what it will shelter. We price it from today’s steel costs. There is no obligation attached, and if a different size would suit you better, you will hear it from us.

Request a Quote Design It in 3D