Metal Building Kits Clinton, NC

Red metal garage with two roll-up doors and a carport lean-to

Clinton NC · Metal Building Kits

If you are weighing metal building kits for Clinton, NC, you can check three things before you spend anything. First, where the steel comes from: we roll-form 29-gauge coil at our Farmville plant. Second, what a building looks like at full size: the walk-in lot at 1046 Greenville Blvd SW lets you pace out a footprint ahead of any delivery to Clinton or elsewhere in Sampson County. Third, the quote: because we put no dollar figures online, you ask for yours by phone at (252) 414-5105 or by sending the quote form. Sampson County pads can be served by kits direct from the plant or by turnkey steel, and when ECOP supplies and erects the building, no separate contractor is needed for the steel. Delivery and setup are free within 100 miles, which covers Eastern VA, Eastern NC and Eastern SC.

Call (252) 414-5105

Get a Free Quote
Reputation and Trust

No contractor needed

ECOP builds and installs the steel building itself.

power 2

Made in Farmville

The roll-forming plant is in Farmville; nothing is manufactured in Greenville.

Locations

Visit the Greenville lot

Our walk-in lot is at 1046 Greenville Blvd SW.

Support

Questions and quotes

Call (252) 414-5105.

delivery truck

Delivery and setup free

No charge for sites within 100 miles of a lot or the plant.

money_1

Rent-to-own available

Qualifying buildings need no credit check.

Customize

Custom to the site

We price the width, height and openings you need for your lot.

Customize

Clear-span kits

Kits for clear-span buildings, quoted to suit your site.

Relocated

Kit or turnkey

Materials by themselves, or the whole building supplied and erected by ECOP.

Gray barn-style metal building with four garage doors

Two ways to buy, and who does the building

A kit can be just the materials, or ECOP can handle the whole building from supply to erection. On the turnkey route nobody else has to be hired to put the steel up. Questions go to (252) 414-5105.

Tan metal garage with two doors and an open lean-to

Metal building kits for Clinton sites

Each kit package comes with panels, framing and hardware. ECOP can also supply and erect the building on a Sampson County pad, and where Sampson County or your insurer calls for certified packages, those are available.

The East Carolina Outdoor Products Greenville lot seen from above the road

Where it is made, where to see it, and how it reaches Clinton

Farmville is where the steel is formed; Greenville has no manufacturing at all. What Greenville does have is our walk-in lot and our business address, East Carolina Outdoor Products at 1046 Greenville Blvd SW, Greenville, NC 27834. Take a look at a sample there, and we deliver to Clinton afterward. Our phone number is (252) 414-5105.

White metal building with open bays, with a truck and equipment trailer nearby

Daily deliveries to towns around Clinton

Free delivery reaches Goldsboro, Smithfield, Fayetteville, Dunn, Warsaw and Mount Olive, and the rest of Eastern NC as well. Ask about kits, inventory that is for sale, and rent-to-own, which asks for no credit check on buildings that qualify.

Steel frame of a metal building going up, with a lift on site

What a metal building kit asks of you and your site

A kit can save money for owners who have time, helpers and tools to spare. Be honest about the site before you commit. Getting a steel frame square and level is hardest on loose sand, soft soil or a slope, and that is the stage where home builds most often run into trouble; a frame that begins out of square causes problems with every panel hung afterward.

Anchoring is the second half of the job. Concrete, asphalt and bare soil each need a different anchor, and your county’s required loads add further conditions. Where a permit applies, the inspector will check the finished building against the certified drawings, and the anchors are part of that check.

Should that be more than you care to take on, ask for the building to be installed instead. You hand over the risk and spend the weekend using the building, not putting it together.

ECOPM28

Siting a kit building in Clinton: storms, water and ground

Two storms show how much water matters when siting a building here. Floyd arrived in 1999 and Matthew in 2016, and each came this far inland as rain; afterward the Tar and Neuse rivers stayed over their banks for days. Wind deserves respect, but on most Sampson County lots the real questions are about drainage, a pad that throws water off, and anchors matched to the soil. Near a creek or river, look up the county flood map before choosing a spot. The five minutes it takes can spare you an insurance headache.

Clinton is the seat of Sampson County, among the largest farming counties in North Carolina. The ground is level sandy loam resting on clay, and the water table lies closer to the surface than most newcomers guess. Sweet potatoes and tobacco do well in that soil, but a slab in a low spot invites standing water. Walk the lot once a summer thunderstorm has passed, note where water collects, and plan the building elsewhere.

Specifications

  • Plant: Farmville, NC — roll-forming manufacturer
  • Walk-in lot: 1046 Greenville Blvd SW
  • NAP: East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834
  • Phone: (252) 414-5105
  • Panels: 29-gauge standard, 26-gauge upgrade
  • Widths: 12’–60′ clear span
  • Service: Clinton · Sampson County · Eastern NC
  • Delivery: Free within 100 miles
  • Region: Eastern NC · Eastern SC · Eastern VA

Common Questions

Who sells metal building kits near Clinton, NC?

We do. The steel is formed at our Farmville plant, samples stand on our Greenville lot, and Clinton and the rest of Sampson County get delivery from us, with installation when you choose the turnkey package. Call (252) 414-5105.

Will I have to hire a builder for a kit?

Not on the turnkey option, where ECOP builds and installs the steel building and no separate builder is needed. A materials-only kit leaves the building work for you to arrange.

Is the Greenville lot where the kits are manufactured?

No. Everything is made at the Farmville plant, and the Greenville location only lets visitors walk in and look.

How much should I plan to spend on a kit near Clinton?

The size, the height, the doors and any certification the site needs all move the price. We leave dollar amounts off our website, so phone (252) 414-5105 or send in the quote form.

Is rent-to-own available with no credit check?

Yes, for buildings that qualify. Mention it when you phone or when you send us the quote form.

Your quote within 24 hours

Give us the size you want, the county and what will be stored. Our quote is based on what steel costs at the moment, it carries no obligation, and we will point out a better size if there is one.

Request a Quote Design It in 3D