Metal Buildings Jacksonville, NC

Gray metal garage with two open doors and a lean-to under trees

Jacksonville NC · Steel Buildings

Start with what you can see for yourself: for metal buildings in Jacksonville, NC, that means the walk-in sales lots in Greenville and the Farmville plant where the panels are roll-formed. From there we deliver across Onslow County, with setup free inside 100 miles. People use the buildings as shops, as storage and on farms. Because we build and install them ourselves, nobody else has to be hired for the steel.

Call (252) 414-5105

Get a Free Quote
Diverse Product Range

Nobody else to hire

The steel building is made, delivered and installed by us; no outside contractor is involved.

Support

Call us

Phone (252) 414-5105 to start a quote.

Diverse Product Range

Where we are

East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834

Diverse Product Range

Frame width

Clear-span frames reach 60′ wide and leave the floor open.

Quality Assurance

Panel gauge

29-gauge panels are the standard.

power 2

Plant and lots

Roll-forming is in Farmville; the walk-in lots are in Greenville.

delivery truck

Free delivery

No charge for delivery within 100 miles.

money_1

Rent-to-own available

Qualifying buildings need no credit check.

Steel frame of a metal building going up, with a lift on site

We build it and we set it up

Making the building, hauling it to your site and putting it up are all ECOP’s work. There is no need to arrange a builder or a contractor of your own for the steel. For questions, dial (252) 414-5105.

Tan two-door metal garage with a concrete driveway

Metal buildings sized for real Onslow parcels

A workshop beside Western Blvd and a storage building out near Richlands need different layouts. Each is priced for the width, length and doors you choose, and none comes from a kit PDF.

Dark green metal building with a roll-up door

Shop, storage or a mix of both

With a clear-span frame the floor stays open, which leaves room for lifts, trailers and workbenches. If the job calls for it, you can add insulation, wainscot or lean-tos.

White metal building with open bays, with a truck and equipment trailer nearby

How far free delivery reaches

A site inside a radius of 100 miles around any ECOP lot gets delivery at no charge, and the roll-forming plant is in Farmville. Phone (252) 414-5105, or find the Greenville lot at East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834.

Tan and brown metal garage with two roll-up doors

Metal buildings in Jacksonville: site, use, then rules

Size and color are what most people think about first, but three earlier decisions do more to determine whether you are still pleased with the building ten years from now. The first is the site. Look for the highest, best-drained ground that you can still reach easily, and measure how far it sits from the property lines, the well and the septic field. The second is the use. List everything the building will hold in the five years ahead, counting the things you have not bought yet. The third is the rules, which the next section covers.

Then the building itself falls into place. Width and length come from what you plan to store and leg height from the tallest item on the list. Roof style depends on how much debris lands on it, and a vertical roof copes best with rain, leaves and pine needles. Put the doors where the driveway runs, not where they would look balanced.

Take your list to the lot, or type it into the quote form, and we will come back with a real number.

ECOPM53

What to ask Onslow County before you build in Jacksonville

Begin with a phone call to the Onslow County inspections office. Ask which permit a building of your size requires, what drawings must go with the application, and whether your parcel is in a flood zone. Wind is why drawings matter here: the closer a site is to the ocean and the sounds, the stronger the design wind, so certification, framing and anchoring that an inland site could skip are often required. Expect the office to ask for certified drawings, and your insurer may ask as well, which is a good reason to request them early.

Next, pull up the flood map for your parcel. The reason is Florence in 2018: days of rain, followed by a surge that sent rivers into neighborhoods that had never flooded. A mapped flood zone changes the job, because pad height and anchoring then count for as much as the building. Near the water, a CAMA permit may also be required on top of the county’s.

Many buyers in Jacksonville, home to MCAS New River and Camp Lejeune, know they may get orders. Salt air works slowly; rinse the panels a couple of times a year and touch up fasteners and trim.

Specifications

  • Phone: (252) 414-5105
  • Address: East Carolina Outdoor Products, 1046 Greenville Blvd SW, Greenville, NC 27834
  • Widths: 12’–60′
  • Lengths: 20’–100’+
  • Panels: 29-gauge
  • Delivery: Free within 100 miles

Common Questions

Do I need to hire my own builder for the steel building?

No. We make the building, deliver it and set it up, so you hire nobody else for the steel. Call (252) 414-5105.

Where can I buy a metal building in Jacksonville, NC?

East Carolina Outdoor Products sells them; the number is (252) 414-5105. The steel is formed in Farmville and brought to sites across Onslow County.

Do you supply shop buildings to customers near Camp Lejeune?

Yes. Start by telling us the width and length you prefer, the door sizes and whether certification is needed.

Do you help with the permit side of a building?

When your inspector requires certified drawings, we provide them. We will also say clearly which parts of the process we do not cover.

Does free delivery reach Sneads Ferry and Swansboro?

Yes. Anything inside 100 miles qualifies, and most of Onslow County lies within that distance.

A Jacksonville price within 24 hours

All we need is a size, a county and a list of what will be stored. Our quotes are based on what steel costs at the moment, you owe us nothing for asking, and if another size would suit you better, we will say so.

Request a Quote Design It in 3D