Metal Roofing Greenville

Long white metal building with a dark metal roof, seen from the air

Two Greenvilles, Two Plants

If you are roofing a building in Greenville, start with the length of your rafter run, because our metal roofing is cut to that exact length. Two cities share the name, and we supply both. In North Carolina, our main roll-forming operation is based in Greenville itself. In South Carolina, a second plant in Williamston is about thirty minutes away from Greenville, SC. On either side of the state line, the panels are rolled locally.

Call (252) 414-5105

Get a Free Quote
Support

Rolled locally

Panels come off our own lines in Greenville, NC and Williamston, SC, and our Greenville sales lots take walk-ins.

Diverse Product Range

Cut to your length

Each panel matches your rafter run, so you get no horizontal laps and nothing wasted in offcuts.

Diverse Product Range

No minimum order

Buy a single replacement sheet or roofing for a whole subdivision.

Diverse Product Range

Days instead of weeks

Our own line follows our own schedule, so your order does not sit in a distributor’s queue.

Diverse Product Range

A full trim package

We supply ridge, rake and eave trim, J-channel, closures and matched screws to go with the panels.

Reputation and Trust

Rates for contractors

Volume pricing and steady turnaround for crews that order again and again.

Aerial view of a metal building with a light blue roof and gravel drive

Metal roofing for Greenville, SC, rolled at Williamston

South Carolina’s Upstate is supplied from our Williamston plant. Downtown Greenville is about half an hour away, so jobs in Greenville, SC are rolled there rather than trucked down from North Carolina, which keeps lead times level with those in our home market. Pickup is from our South Carolina lots, with more at Inman, Anderson, Pelzer and Easley around the metro, and the lots in Greenville, NC take walk-in customers.

Aerial view of a dark metal roof with a covered porch

Greenville, NC: coil in one end, panels out the other

The roll-forming line is in Greenville, NC, and our lots are at 1046 Greenville Blvd SW. Customers in Pitt County get about as direct a route as buying gets. Coil goes into one end of the line, panels sized to your rafter run come out of the other, and you pick them up the same week. Order on Tuesday and collect on Thursday is the usual turnaround here, not the fastest we can manage.

ECOPM54

What contractors in Greenville buy most

Greenville orders are mostly 29-gauge panel in standard colors, cut to the exact length of each rafter run. The trim that finishes the job goes with it: foam closures, J-channel, the ridge cap, trim for the eaves and rakes, and screws matched to the panel color. Many roofs in both markets go over existing shingles, and a recover job needs fasteners long enough to reach solid framing. If that describes yours, tell us when you order and we will specify the right screws, so you do not find out the hard way while standing on the roof.

Long charcoal metal building with a roll-up door on a freshly graded site

How metal roofing holds up in Eastern North Carolina

Humid summers and tropical storms are what a roof in this part of the state has to live with, and a metal roof that is fastened correctly copes with both. It resists uplift far better than an aging shingle roof, it drains a downpour fast, and it does not grow the black algae streaks that mark so many shingles in the humid Southeast. A lighter color also reflects much of the summer heat, which you feel in a shop or barn with no air conditioning.

Wind-driven rain gets in through details: the fasteners, the closures at the eave and ridge, and the trim. On the coast those count for more than the gauge of the panel. Rinse salt off a couple of times each year, and look over exposed fasteners after any named storm.

Condensation needs a plan too. On spring and fall mornings, damp warm air condenses on a cool panel and drips from the underside. Insulation or a vapor barrier beneath the panels, with vents at the ridge and eaves, stops it, and putting it in while the roof goes on costs far less than adding it later.

White metal building with open bays, with a truck and trailer alongside

What to ask the county before you build in Eastern North Carolina

Before you pick a roof color, phone the county and ask what a building at your address needs: which permit, whether the inspector wants certified drawings, and whether the lot sits in a mapped flood zone. The answers differ from one county to the next. Flood zones follow the rivers and sounds, and the wind a building is designed for grows stronger from I-95 toward the coast.

The questions come from the weather. Storms such as Floyd in 1999, Matthew in 2016 and Florence in 2018 are the reason, and most of those storms came as water rather than wind. A building here is only as good as its anchoring and the ground under it. Tell us where yours is going and we will quote the framing, anchors and drawings that fit that spot.

Specifications

  • Greenville NC lots: 1046 Greenville Blvd SW · 1046 Greenville Blvd SW
  • Nearest SC plant: Williamston, SC — 980 Beaverdam Rd
  • Upstate SC lots: Easley · Pelzer · Anderson · Inman · Greenwood
  • Gauge: 29-gauge standard, 26-gauge available
  • Panel length: Cut to order
  • Minimum order: None

Common Questions

Who sells metal roofing in Greenville, SC?

We do, from our Williamston plant, which supplies Greenville, South Carolina, and from the lots around the metro that handle local pickup. Panels are formed at the plant and cut to your length, and no order is too small. Call (252) 414-5105.

Who sells metal roofing in Greenville, NC?

We do. Our main plant is in Greenville itself, and the lots are at 1046 Greenville Blvd SW. Panels leave the line sized to your rafter run, and on standard materials you can order Tuesday and collect Thursday.

Do you deliver roofing panels around Greenville?

Yes, or you can pick up from whichever lot suits you. For buildings, delivery and setup cost nothing inside 100 miles, and freight on materials outside the local area is priced openly. For most jobs near Greenville, collecting is cheaper and quicker.

Can Greenville customers get panels cut to length?

Yes, and that is why it pays to buy from a roll-former. A rafter run of 27 feet 4 inches gets a panel of 27 feet 4 inches, one continuous piece with no horizontal lap and no offcut. A supplier that stocks only fixed lengths cannot offer that.

Roofing quote back within 24 hours

Let us know how big the job is, which county it is in and what the building holds. We work from current steel prices, you owe nothing for asking, and if a different size would suit you better we will tell you.

Request a Quote Design It in 3D