Metal Roofing Panels

Aerial view of a dark metal roof on a long white building

Roll-Formed & Cut To Order

When you are roofing a barn, a shop or a house, what you need to know is how long each panel must be, eave to ridge, and how many it takes to cross the building. Our metal roofing panels come off our own roll-forming lines, and each one is cut to the length your roof run calls for. Each panel gives 36 inches of net coverage, comes in a full range of colors, and is made in 29-gauge as standard, with 26-gauge available. You can buy a single sheet or enough for a whole project.

Call (252) 414-5105

Get a Free Quote
Diverse Product Range

36 inches of net coverage

Counted once the panel is installed, rather than by the raw sheet width.

Diverse Product Range

Any length you need

Each panel is made to match the rafter run, so it is one continuous piece with no lap.

Quality Assurance

29-gauge and 26-gauge

A standard weight and a heavy-duty one, both formed on our lines.

Customize

Full range of colors

Screws with painted heads to match are available in every color.

Diverse Product Range

One sheet is enough

Patch a single barn roof or cover a whole subdivision; there is no minimum order.

Diverse Product Range

Quantities done for you

Send the dimensions and we will draw up the whole materials list.

Aerial view of a white metal building with a dark metal roof

What net coverage means for metal roofing panels

Once a panel is formed and lapped to its neighbor, it covers 36 inches of roof. That figure is the net coverage, and it differs from how wide the flat sheet was before forming. To find your quantity, count how many 3-foot widths fit across the roof and round up; using the raw material width instead gives the wrong count. That mix-up is the usual cause of a wrong panel order, and it is why we prefer to begin with your roof dimensions rather than a sheet count.

Aerial view of a metal building with a light blue roof and gravel drive

A panel cut to length leaves no seam across the roof

Suppliers who stock fixed lengths put you in a bind: either you overlap two sheets somewhere on the slope, or you order oversize panels and cut them down. A cross-roof lap can leak, and it catches debris. Because we cut each panel to order, a rafter run of 27 feet 4 inches receives one panel of exactly 27 feet 4 inches, unbroken from ridge to eave, with nothing left over. On a re-roof that can be worth more than the difference between one supplier’s price and another’s.

White and gray metal building with three large openings

Choosing between 29-gauge and 26-gauge

The industry standard for houses, farm buildings and pole barns is 29-gauge, and for most jobs that is the right choice. The thicker 26-gauge earns its extra cost where panels span long distances between supports, where hail is likely, or where a shallow pitch means people will often walk on the roof. On a shed roof with plenty of purlins, the extra money is better spent on better screws.

Long white metal building with black wainscot and a roll-up door

What to have ready when you order

Start with the roof measurements: the rafter run, eave to ridge, and the width of the building, plus the pitch and purlin spacing if you have them. From those we work out how many panels you need and how long they must be, along with the ridge cap, eave and rake trim, closures and screws. A short call is enough, and the result is more dependable than a sheet count taken from a sketch.

Long white metal barn with arched openings along the side

How metal roofing panels hold up in Eastern NC weather

A metal roof that is fastened correctly handles our weather well. It resists uplift much better than shingles that have aged, it drains a downpour fast, and it does not grow the streaks of black algae that stain shingle roofs across the humid Southeast. A lighter color adds a benefit you can feel, because it reflects a good share of summer heat, a relief when the shop or barn has no air conditioning.

Along the coast, a roof’s details decide how well it ages. The fasteners, the closures at the eaves and ridge, and trim that keeps wind-driven rain out all matter more than gauge on its own. Rinse off the salt twice a year or so, and after a named storm, check whatever fasteners are exposed.

Plan for condensation too. On cool spring and fall mornings, a cold panel meets warm, wet air and the underside begins to drip. Ventilation at the ridge and eaves, plus insulation or a vapor barrier beneath the panels, solves it. Putting that layer in while the roof is going on costs far less than adding it afterward.

ECOPM54

Permits and flood maps for a new roof in Eastern NC

Before the panels are ordered, call your county’s building department and ask what permit a roof or building at your address needs. Find out which certification the inspector will want to see, and whether the flood map puts your lot in a flood zone, since flood zones line the rivers and sounds. What counts depends on the county.

The weather record explains why. People here remember Floyd (1999), Isabel (2003), Irene (2011), Matthew (2016), Florence (2018) and Dorian (2019), a few of them as wind and most as water. Design wind speeds also climb as you leave I-95 for the coast, so a roof near the water is designed for a higher figure than one inland. A building here is only as sound as how it is anchored and the ground beneath it. If the panels are for a new building, tell us where it will stand and we will price framing, anchors and drawings to suit the spot.

Specifications

  • Net coverage: 36″ per panel
  • Gauges: 29-gauge standard, 26-gauge available
  • Lengths: Cut to order, any length
  • Finish: Rust-resistant coated, full colour range
  • Fasteners: Painted-head screws, colour matched
  • Closures: Inside and outside foam

Common Questions

How do I calculate the number of metal roofing panels my roof needs?

Count how many 3-foot widths fit across the roof, since one panel has 36 inches of net coverage, and round up. Then multiply that count by the number of roof planes. Each panel runs the full rafter run, eave to ridge. Send us the dimensions and we will work out the panel count, trim and screws, which takes minutes and avoids the usual ordering mistake.

How wide and how long is one of your roofing panels?

Each covers 36 inches once installed and lapped, and we cut it to whatever length you specify. Panels are roll-formed only when an order arrives, so no standard length exists: the panel is as long as your roof run.

Can I put metal roofing panels over my existing shingles?

Often yes: leaving the old roof in place spares you the tear-off and the landfill fees. It hinges on the state of the roof deck, local code and the number of layers already on the roof. Longer screws are needed to reach solid framing. Check with your building department, and let us know it is a recover job so that we specify the fastener length correctly.

Which gauge of roofing panel is right for my job?

The industry standard is 29-gauge, and it suits most house roofs, farm buildings and pole barns. Choose 26-gauge when panels must span long distances without support, where hail is likely, or on a roof that people walk on often. If the roof is well purlined, better fasteners usually give you more for your money than a heavier gauge.

Can I buy metal roofing panels one sheet at a time?

Yes. There is no minimum, and one replacement panel is cut to length exactly as a full project’s panels are.

A price for your roof within 24 hours

Tell us how large the roof is, which county it is in and what will be kept underneath. Our price follows steel costs as they stand now, asking obliges you to nothing, and if you would be better served by a different size, we will say so.

Request a Quote Design It in 3D